• Deutsch
  • English
  • Français

Wire Rope Trellis Fitting with Special Nut M12, WM 12225

[Translate to Englisch:] Seilhalter WM 12XX5 für vergrößerten Wandabstand

Product sheet

Description / Price

Cable mount with increased wall distance (11 - 12 cm), made of stainless steel, threaded shaft M12, crosshead d = 20 mm with grub screw, lock nut, long nut, special nut M12 with press-ring/gasket. The head is also available separately. >>> Price

 

Use

Special mount for wire rope, 3 (and 4) mm for medium and heavy kits in accordance with the specifications of the respective wire rope system (if purchased as a pre-assembled kit). The distance from mount to mount should ideally not exceed 1.8 m at horizontal ropes and 2.2 m at vertical ropes. Simple or crosswise rope guidance. Wall distance approx. 12 - 12 cm. Mostly adhesive (glue) mounting; special cases see below. For support in choosing a trellis fitting, refer to our section on cable (cross) mounts.

 

Recommended Tools

Hammer drill HB 16210 for all drillings with or without sieve sleeves.

 

Installation

If necessary, refer to our instructions on drilling and the information on composite mortar. For optimal sealing, the surface should be reasonably flat or made so (sanded down). Drill 16 mm, depth approx. 12 cm. When using sieve rawl plug SD 16130, drill hole diameter 16 mm, depth 14 cm. Dismantle completely; also loosen the countered crosshead. Press in the composite mortar, insert the threaded shaft in a rotating manner; protrusion outside according to the wall distance (11 - 12 cm).  If necessary, secure against sagging from below (photo). Spread or remove any mortar that swells out in order to create an almost smooth support for the seal. After setting, push on the wall together with all small parts, tighten adjusting nut firmly, fasten cross head with lock nut. Further installation carried out as described for heavy kits.

When mounting with metal anchors/plugs, DM 12030, please refer to the product sheet of that anchor; if necessary, you can shorten the threaded shaft, or let it be shortened by FassadenGrün. For installation into solid wood, request a shorter length if necessary. Drill diameter 10.5-11 mm. Grease threaded shaft, screw the long nut and special nut on the shaft firmly against each other with 2 open-ended wrenches and then grasp the shaft at the nut further away with an open-ended wrench and screw it in directly. By grinding in a short longitudinal groove at the end of the threaded shaft, it can act like a "self-tapping screw" facilitate screwing-in. 

In the case of thermal-bridge-free installation in 2-ply mounting blocks laminated with aluminium plate (ETICS special case) such as UMP-ALU-TRI from Dosteba, please ask for the version of WM 12165 and only use 3 mm wire rope. Drill centrally through BOTH aluminium plates of the mounting blocks with a 10.2 mm (10.5 mm) metal drill; cut an M12 metal thread into the mounting block by hand with a tap and tap wrench/iron, screw in the pre-assembled cross mount approx. 40 mm deep until the outer wall distance of 12 cm is reached; then align the cross head and tighten the adjusting nut. Further assembly is carried out as described for heavy kits.

 

Origin

Made in Germany (Saxony), hexagon nuts from the Far East.

[Translate to Englisch:] Seilhalter mit Kegelmutter WM 12XX5
[Translate to Englisch:] Ranksystem mit Haltern und vertikalen Seilen
Cable gird, here a system for mounting advertisements
Wire roipe holder for stainless steel cables
Wedge (with a matchstick, for example) to prevent displacement of the anchor during the gluing process
Wedge with a matchstick (so doesn't drop during adhesion)
Preparation for mounting with plug DM 12300
Preparation for mounting with plug DM 12300