• Deutsch
  • English
  • Français

Wire Rope Trellis Fitting M12 'Massive,' WM 12153

Stainless steel wall mount

Product sheet

Description / Price

Cable mount -- 'cross mount' -- made of stainless steel A4, smooth shaft d = 12 mm, made of particularly strong (bend-resistant) A4-80, with integrated anchoring system (patent protected). Phillips d = 20 mm with grub screw, lock nut, thrust washer for the drill hole closure, neoprene gasket, plastic spacer, expansion cone and metric plug (both from galvanised steel). Wall clearance 90 mm. Simple installation. A similar head is also available separately. >>> Price

 

Use

Standard wall mount for massive kits. For 3 and 4 mm cable. For a simple or crosswise cable guidance, if necessary also triple guidance. The distance from mount to mount should preferably not exceed 1.8 m with horizontal cables and 2.2 m with vertical cables. Compatible with many wall types; please check suitability via the link. Due to the expansion pressure, not suitable for border/edge areas; minimum distance from the edge of free-standing walls-- approx. 25 cm. Can also be mounted directly into solid wood d > 8 cm. Not for walls with insulation, wood panelling, or pre-fab construction. Plants that quickly form trunks-- like wisteria, knotweed and bittersweet-- need to be guided parallel to the cable, avoid continuous looping around steel wire rope as described with wisteria. Please also refer to the information on cable 'cross' mounts for support in choosing an appropriate trellis fitting. 

 

Installation

If necessary, please refer to the guidelines we've provided on drilling. Drill hole: 16 mm in diameter and 9 cm deep; expand the front half of the drill hole, if possible, to about 16.5 mm diameter by gently abrading the hole wall during drilling. For optimal sealing, the surface should be reasonably flat or made so (sanded down). The already pre-assembled wall mount is led into the cleaned bore-hole, struck lightly on the head (cross head) (figure 06) if necessary, until the rubber seal comes in contact with the wall. If the mount can only be introduced with difficulty, the hole can be drilled again and widened by applying lateral pressure of the drill. If, on the other hand, the drill diameter becomes too large, rotate the rawl plug (dowel) a little closer/tighter before insertion. By slightly buckling the spacer body (the mount), a better 'grip' is then possible at the borehole wall, and the element does not rotate when tightening. Then use an open-ended wrench on the double nut and turn (screw in) (Figure 07). The wrench must engage the broad front nut. After a few turns - clockwise -as when inserting an ordinary screw - the inner metric plug is spread open, recognizable by the squeezing of the outside protruding plastic sleeve (spread indicator - Image 08). If the protruding plastic sleeve is completely crushed (Figure 09), the holder will be aligned according to the cross-slots. Proceed with installation as described for massive kits.

 

Special Features with Vertically Perforated Bricks

Installing in perforated bricks with a dense structure is usually no problem. In porous, perforated bricks, such as Poroton (hollow bricks), Eder, etc., use is possible if the bricks are of category Hlz 12 or higher... i.e. vertically perforated bricks with compressive strength class 12. With a lower strength class, the inner webs should be as wide as possible. The structure of the chambers must ensure ensure that the rawl plug (anchor) head can grip at least the second web/footbridge; this must begin at least 6 cms inside behind the plaster outside edge (not stone outside edge!). The assembly ends in vertically perforated ('hollow') bricks (with picture 08/09; the last strong turn of the wrench (picture 10) is omitted. If there is still a clear 'crackling' in the brick during assembly, you can unscrew the cross mount again and exchange the entire product for adhesive plug (anchor) WM 12191. When in doubt, always use the element WM 12191, preferably with adhesion (gluing).

 

Special Features of Aerated Concrete

In aerated pore concrete ("air/gas/cellular concrete," e.g. "Ytong"), the wall mount can only be used to a limited extent if no strong twiners like wisteria, knotweed, tree shrike, etc.. are planted. It is then better to choose 3 mm of cable (instead of 4 mm), and the grub screws shouldn't be tightened too strongly. When in doubt: the mount can be set at a closer distance, or as an alternative, choose the heavy construction style with its deeper anchorage in order to prevent a breakage of the stone. In aerated concrete, the wall mount is hammered in and then tightened. It makes sense to drill a short, max 1.5 cm deep pilot-hole (d = 16 mm) to penetrate the outer plaster layer in order to avoid spalling when driving in. Then drill a pilot hole 6 - 8 mm in diameter-- even better a mandrel (awl)-punched hole-- in order to compact the surrounding material. It make take then 10 or more 'turns' until the anchor/plug has sufficiently compacted the surrounding stone material and and taken 'grip.'  

 

Special Features - General

This cable mount can be screwed out of the anchoring (rawl plug) again.
 

Origin

"Made in Germany" (Saxony), shaft from North Rhine-Westphalia, plug system from Baden-Wurttemberg; hexagon nuts from the Far East.

Components of the wall mount
Picture 02: Components of the cross mount with rawl plug
Massive cable mount
Picture 03: Cable mount WM 12153
Wall mount with wire rope
Picture 04: Cable mount WM 12153 in brick wall, grapevine
High-rise warehouse in Dusseldorf
Picture 05: Aerated concrete walls by a high rack warehouse with WM 12153, about 12 m high, Dutchmans pipe, honeysuckle, Clematis vitalba
WM 12153 into massive wood
Picture 06: installation into wooden post
Einschlagen der Wandhalterung
Picture 07: Gently hammering the mount into the wall
Montage mit Maulschlüssel
Picture 08: Screwing in (here an older version WM 12163)
Wandhalter Montage
Image 09: Expansion of the rawl plug
Mounting of trellis fitting
Image 10: Mount in the facade after installation